Reserved Area

PRODUCTS

Sliver

Launched in 2015, SLIVER was the first built-in anti-condensation hood on the market.

SLIVER adopts patented solutions to heat not only the flap that can be opened, but all the lower surfaces of the hood immediately after being turned on, bringing them to a certain temperature that avoids the formation of condensation. If this were not the case, unheated parts such as inclined filters of other products on the market would inevitably produce drops on the surface.

The captured air, still full of humidity, passes through cold surfaces inside the hood where it releases the contained water which is then collected in an internal tray.

This internal tray contains electronic sensors that continuously monitor the water level, stopping the hood motor as soon as the level reaches the maximum. The command LEDs flash to signal this condition.

The emptying of this tray is very simple and fast and is performed by pressing a lever and placing a glass under the drain valve. Only after emptying the tray will the hood work again.

SLIVER has been tested in our laboratories in the most critical conditions, with 4 boiling pots and at a distance of 50cm. from the induction hob. Even in this extreme condition, after more than an hour of operation, no drop falls into the induction hob below.

 

Using the same conditions, we also tested the main anti-condensation products on the market and, after more than an hour of operation, SLIVER is the only one to prevent the formation of drops in all its surfaces and therefore prevent them from falling on the induction hob below.

SLIVER SECOND TO NONE !

Product plus
SLIVER
OTHER MODELS IN THE MARKET
Heating of all the lower surfaces of the hood
Heating of all the lower surfaces of the hood
Heating of all the lower surfaces of the hood
Electronic sensor for tray full of water
Electronic sensor for tray full of water
Electronic sensor for tray full of water
Automatic and complete shutdown of the hood when the flap is closed
Automatic and complete shutdown of the hood when the flap is closed
Automatic and complete shutdown of the hood when the flap is closed
Easy opening of the sliding flap
Easy opening of the sliding flap
Easy opening of the sliding flap

Dimension

60 – 75 – 90 – 120 cm

Finishing

Inox / Anthracite

Version

Duct out

Controls

Electronic Soft Touch 3S + B

Lights

LEDSTRIP 4Wx60cm, 6Wx 75/90/120cm-3000K

Max airflow

635 m3/h

Total absorption

426 W

Sound power

63 dB(A)

Energy Class

A

Play Video
  • SLIVER 60/A INOX – SLIVER 60/A ANTRACITE
  • SLIVER 75/A INOX – SLIVER 75/A ANTRACITE
  • SLIVER 90/A INOX – SLIVER 90/A ANTRACITE
  • SLIVER 120/A INOX – SLIVER 120/A ANTRACITE

Extra

  • Adjustable and delayed self-switching off: This function allows you to programme delayed cooker hood shutdown which, in the shortest time possible, provides the right level of air purity in your kitchen.
  • Light indicator for grease filter maintenance:The cooker hood automatically informs you when the metal grease filter designed for trapping grease in the air requires cleaning. It is of utmost importance to clean these filters to ensure cooker hood components are protected and to prevent bad odours caused by a build-up of grease.
  • Light indicator for the regeneration of Long Life filters: the Long Life odor filter captures all the smells present in the cooking fumes, guaranteeing pure air in your kitchen. It does not need to be replaced as frequently as a normal activated carbon filter, it can be regenerated every 3-4 months, and in any case according to the frequency of use of the hood, with a usual washing in the dishwasher at about 70 ° C without any type of detergent, followed by drying in the oven for 30 minutes at 70 ° C. To keep its efficiency high, it is recommended to replace the Long Life filter after 6/8 regeneration cycles.
  • Perimeter extraction: This consists of a mechanical system that literally forces, pushes, the cooking fumes extracted along a slit that runs along the perimeter of the cooker hood. This system increases extraction performance whilst reducing cooker hood noise emission. Design and appearance are also improved as the grease filters are no longer visible.
  • Light warning of full condensation liquids collecting tray.
  • Courtesy light, possibility to keep the light on even with the flap closed.
  • Adaptor 150-125mm

Download

Accessories

Long Life filtering kit: cod. 005LV03002

One-way valve: cod. 0051H02000

Request information

Share